请教 Yeager 师傅 ，四轴加工的进给率怎么计算？在UG_POST_Buiding中怎么设定？

clhbxg

请教大师，四轴加工中F进给率怎么计算它的下正确性？  在ug_POST_Buiding中怎么设定PB 函数？现在遇到一个难题，四轴同动做铝合金产品高光倒角，弄了好几天都不行，请帮帮忙，看看我的后处理：
- N- D- v- z) c; |0 |- ^%
O0100
G21
G91 G28 Z0.
G0 G17 G40 G90 G49 G80
(TOOL:COUNTERSINKING_TOOL)
(D=6.00000000000000000)
& `$ L! c9 e; u) J(R=0.00000000000000000)
1 w! y( E6 g. D  |$ {) t, {  EN0010 T03 M06
- U- J- r9 G! a+ wG0 G90 G54 X-40.041 Y-2.827 A-17.416 S6500 M03
# [3 d9 T2 e" J. w2 m8 Y# jG43 Z51.673 H03
Z39.673
+ ]% Q% _6 k# }; GG1 X-39.542 Y-2.851 F800.
2 i' _: ~5 x& YG17 G3 X-39.071 Y-2.842 R3.
X-38.607 Y-2.754 R3.
: e" S% b. Q3 \; HX-38.164 Y-2.595 R3.
X-37.75 Y-2.368 R3.
  t8 H) T7 Y7 E# gX-37.377 Y-2.08 R3.
X-37.054 Y-1.737 R3.
  q0 s) g* h: X& D6 [; fX-36.788 Y-1.347 R3.
X-36.587 Y-.921 R3.
5 e) Q8 Q: a* z' q7 t9 ^( cX-36.455 Y-.468 R3.
X-36.4 Y0.0 R3.
. ^( O9 C3 x5 X3 M6 U3 sG1 X-36.372 Z39.668 A-18.24 F1400.474
3 }6 f" c* b4 m8 O/ _X-36.334 Z39.66 A-18.854 F1874.304
$ w% P& {5 {9 ~5 P. Q+ yX-36.292 Z39.654 A-19.311 F2506.707
X-36.208 Z39.647 A-19.991 F1673.387
X-36.092 A-20.663 F1669.254
0 G) E$ ?( t, R, z, ~X-35.918 Z39.651 A-21.449 F1400.84
X-35.764 Z39.653 A-22.029 F1860.776
4 ]! o+ p" I1 @X-35.637 A-22.457 F2482.26
X-35.426 Z39.651 A-23.085 F1655.864
X-35.192 Z39.647 A-23.694 F1659.552
X-35.043 Z39.644 A-24.045 F2807.5
X-34.759 Z39.636 A-24.643 F1593.995
' j+ n6 ?5 r8 ~: ]9 vX-34.529 Z39.629 A-25.077 F2115.017
* C- W; v! l* i6 }* ?X-34.159 Z39.616 A-25.7 F1408.321
' u3 I0 w6 ?  c- `2 OX-33.762 Z39.603 A-26.287 F1408.82
* Q" _- k" r+ @X-33.551 Z39.598 A-26.569 F2784.663
6 ^4 a% m5 ^; v/ jX-33.166 Z39.592 A-27.035 F1593.747
X-32.864 Z39.589 A-27.363 F2118.663
X-32.395 Z39.585 A-27.826 F1409.135
X-31.907 Z39.577 A-28.257 F1399.297
X-30.606 Z39.549 A-29.288 F539.336
X-29.386 Z39.522 A-30.255 F575.205
X-28.242 Z39.496 A-31.161 F613.624
* L3 a; R1 l# ~+ B$ dX-26.097 Z39.448 A-32.86 F327.327
2 f9 x; O0 Y! y9 `X-24.22 Z39.407 A-34.347 F374.147
, r* B) V& @) H/ r6 [. FX-22.578 Z39.37 A-35.649 F427.698
X-21.14 Z39.339 A-36.788 F488.599
* z5 d# J; ^6 ^; g+ ]6 x& QX-19.882 Z39.311 A-37.785 F558.527
( Q4 c& h$ f8 R" O7 sX-17.68 Z39.262 A-39.53 F319.162
  Y5 {2 X# D; a/ s# {* Z& s( lX-16.028 Z39.226 A-40.839 F425.54
X-14.788 Z39.199 A-41.821 F567.105
X-12.928 Z39.158 A-43.295 F378.084
0 e+ `! k7 q; H8 n- y! ZX-11.067 Z39.117 A-44.769 F378.017
+ |" d! i( \+ U7 ]  y- s8 i1 bX-10.808 Z39.114 A-44.997 F2647.349
: v5 H/ f! u  [$ A" sX-10.431 Z39.115 A-45.363 F1768.799
5 l, e3 J/ }& H

Yeager

叫我嗎???

公式不是我發明的，我可以分享！
% M  u- \- @) j0 j. c=>設定速度F / 兩座標奌間距離

8 r: W) e3 d, ?) h; p要怎麼把算式寫到PB里，這就是我的專業了！
提到專業，不免要俗氣談到$$$了....有預算嗎？

clhbxg

感谢，能不能说清楚一点呀，有点不明白，可以贴个图吗？

clhbxg

请问要怎麼把算式寫到PB里?

clhbxg

能把PB的内容贴出来吗？