半径补偿

suifeng00

在ug编程中，半径补偿怎样加进去的？

56198605

%
N0010 G40 G17 G90 G70
5 Z; S" @4 y1 N' o5 _7 kN0020 G91 G28 Z0.0
:0030 T01 M06
N0040 T02
N0050 G0 G90 X-10.5685 Y47.3674 S0 M03
N0060 G43 Z6.5 H01
; R7 {$ e8 r; J! bN0070 Z2.
  a2 u$ B$ T8 v0 Y# q& b' _  B+ YN0080 G1 Z-1. F250. M08
8 V! g' J! e4 }1 p4 Q* Q. NN0090 G41 X-8.3 Y48.418
9 l4 C! I" A4 k, a+ \N0100 G3 X-5.3 Y54.1626 I-4. J5.7446
. n) r4 q: g2 A: TN0110 G1 Y100.
N0120 G2 X0.0 Y105.3 I5.3 J0.0
N0130 G1 X80.
2 p6 e/ k. t% J; J% h4 ZN0140 G2 X105.3 Y80. I0.0 J-25.3
' \6 H, S: w1 n; N1 fN0150 G1 Y0.0
N0160 G2 X100. Y-5.3 I-5.3 J0.0
N0170 G1 X0.0
! t# F: E4 L+ [2 d% c9 h+ XN0180 G2 X-5.3 Y0.0 I0.0 J5.3
- l% X$ U% g1 c4 O2 W/ c) ^N0190 G1 Y54.1626
N0200 Y55.1626
N0210 G3 X-8.3 Y60.9072 I-7. J0.0
- `1 q$ r4 n5 r4 L3 E; PN0220 G40
( d, Z6 p  g3 V' TN0230 G0 X-10.5685 Y61.9578
, O# C$ q/ P8 ~$ J5 q/ K# JN0240 Z2.
' |9 ?0 r- s/ s' M$ p' c" SN0250 Z6.5
7 Z" e) x7 K8 Z/ a$ ZN0260 G91 G28 Z0.0
% f2 w  e- X3 y; m:0270 T02 M06
9 ?+ Q8 K2 U  Y" iN0280 T01
+ y) V* s& `  c- ~5 e0 e/ ZN0290 G0 G90 X-11.0006 Y47.7068 S0 M03
N0300 G43 Z6.5 H02
N0310 Z2.
+ d6 P( R; m8 d, _3 KN0320 G1 Z-1. F250.
4 d' V* h4 {# p4 S) IN0330 G41 X-8.7321 Y48.7574
0 B$ M1 l. d2 N3 }N0340 G3 X-5.7321 Y54.5019 I-4. J5.7445
N0350 G1 Y100.
3 p! K! B6 F1 @8 E0 xN0360 G2 X0.0 Y105.7321 I5.7321 J0.0
0 u  O# Z8 ]# MN0370 G1 X80.
N0380 G2 X105.7321 Y80. I0.0 J-25.7321
N0390 G1 Y0.0
& `' q( Q6 g9 _$ \4 K- wN0400 G2 X100. Y-5.7321 I-5.7321 J0.0
0 K' U9 h$ c6 O7 y; \# F+ zN0410 G1 X0.0
% S' X$ k- y/ f+ w% u6 x% T) m5 bN0420 G2 X-5.7321 Y0.0 I0.0 J5.7321
N0430 G1 Y54.5019
- d; @' E: `7 j0 x, TN0440 Y55.5019
) x$ ^2 {! m% aN0450 G3 X-8.7321 Y61.2465 I-7. J0.0
N0460 G40
N0470 G0 X-11.0006 Y62.2971
N0480 Z2.
N0490 Z6.5
( C8 v; F" M' TN0500 M02
( W+ S+ N7 U. ^+ c3 l: Z: F- R% r%

suifeng00

在UG中，应该怎样去做呢？

guoa700

机床中添加事件

liuzhong

顶楼上的！