|
楼主 |
发表于 2011-11-15 21:47
|
显示全部楼层
1 % : character at beginning of file
: T4 S3 O& i" f' @6 b3 G91G28Z0.0 : character at end of file- w& I" `: [6 ^2 v, c. q2 D
M30
( E' j( T9 s3 e. j1 T% P. G%; o0 m: \1 r. H8 ?; t2 f* L
0 ( ) : commentary: 0=no,1=yes,2=yes,with block nos. ^ M" v& H! w4 H7 i+ }9 o8 f/ `$ u
0 S : spindle speed command# j- \% a$ a4 E; d
1 : output format : 1=mm,2=1/100,3=1/1000( l# K2 Z# E7 E# {2 O2 O/ A0 \
1 : condensed mode: 0=no,1=yes
& ^) d. X- R' C3 z/ m3 [+ I0 500 : maximum block number per file: 0=n/a
+ x, u3 s$ p5 Q- [) L F3 @ U- }0 5 : initial block number: 0=no block numbers4 F$ Z! M' a2 t6 y1 o, E
0 1 : incrementation between blocks- [/ F- P# ~& S2 g
0 : start up command! G/ L, P) F2 v( z) u |5 h1 |
0 : stop command
" g, U; V. d/ j4 Z' S% p1 G00 8000 : fast speed: 1=1st point fast speed,2=feeding2 X' a8 `$ e0 a2 V
1 G01 : feeding speed: 2=code F.. with 1st point only* Z1 X1 }6 m1 O+ [# E" E
1 : point directed: 0=centre,1=tip
) P- w7 S% _% }4 t( x' ]1 A" I' O% N0 : no of free-format lines, each file (20*75 max) , n: T" D- ~# B) m8 I2 C+ P* k
1 : Output file extension: 0='.blc'
0 j: e! N/ P4 N; c! k0 R1 p( W0 : characters to add at the end of each line: 0=n/a) Z$ n2 N L2 {+ M3 G9 i! _
0 : maximum size in characters per file: 0=n/a. W- g3 S/ }8 C! ?+ N: i' @" o/ \
0 : maximum distance machined per file: 0=n/a
$ O, n* }5 F/ ~& q/ V0 : no of lines between blocks: 0=n/a6 z$ w1 `* b4 s/ l) _3 v
2 : first point: 0=XYZ,1=Z only; ?! H( P: B0 G+ t0 @. g9 m4 `
0 : transformation to the machine axes: 0=n/a7 m+ A) y$ A; j U4 \' X/ @
5 : no of free-format lines, first file only
4 q/ H$ x0 V) {3 f0 ~& zG90G80G40G49G173 p* l2 ~7 L4 ]/ q
G91G28Z0.0
% f- r% E. w+ qG91G28X0.0Y0.0( h5 W+ ]( @3 W3 k( r! s
G90G00G55
/ j7 X6 j/ n; H7 l7 B# h1 cM08
* L& b- T, h: h8 b- E5 P( t$ I0 : break the file at each z-level?
7 u: d. N. E6 }' j5 `, v- g0 : coordinate mode: 0=absolute,1=incremental+ ?$ L8 ]: m, }+ i7 L9 L/ `- r
0 : speed change rapid -> feed: 1=before, 2=after2 r" z- t& ~8 F: ~4 p# D
0 : speed change feed -> rapid: " "1 c2 {1 f! v. I3 v5 y
1 1 : commentaries required : header,distances+ X6 W7 q5 c2 O& ?3 v
0 X Y Z : Axis labels : 0=n/a+ Y, q9 E; C/ ^. s+ P" Z
0 0 1 F : Format of speed commands : 0=n/a
: C0 n4 v) }: {, K4 D0 : Tool axis rotation : 0=n/a
/ p; @, L$ q6 f$ w0 u0 G40 G41 G42 : Tool correction : 0=n/a
) v! x p8 A k/ F0 W1 Z0 A0 50 H~e~g~h~i~j~kM13 : supplementary block @6 d. V% g1 h" f0 w
#44 1 : Change the output file name format" j: S. ^: d7 V" v8 ]+ u* m: K' l
#52 5 : Add lines at the begining of each toolpath
( `$ m7 ?3 v$ K& t z5 BM06T~n
1 ~) A7 Y$ g5 \& SM08" O8 s# s8 _2 k& f2 f
S~bM03G90: T; G* X1 Y$ Q; x# V! @
G00~h~i
( Z, Q, n0 `" \6 B- O4 ?G43H~n~j9 |4 O" a# d& s: E4 s5 S
#56 2 : Add lines at the each toolpath/ ~. e# h3 @) u& ?; r2 ?; P
G91 G28 Z0.
9 F7 I2 L/ e% R5 r- X* c$ e- KM05
4 {9 ~' \$ C6 K" |
$ m+ }7 d! F& ^! R4 w @(#)nc.ang 1.3 2/12/93 WORKNC
$ {% `* S3 L( V; t# z: y6 e. d J9 _8 x
請問要在哪邊改自動待刀跟攻牙??8 k, h' M7 d$ X) ]' @) V
小弟在此誠心請教各位大大!! |
|