求大侠写一个注册表或者批处理（bat）加UG环境变量

盗走我的坟

KASA_DIR=D:\Kasa
- Z4 Q3 y3 X8 ]" h$ wugII_SITE_DIR=D:\Kasa
/ A% {6 E1 r- W$ bUGII_CAM_POST_DIR=D:\Kasa\Postprocessor\
UGII_CAM_POST_OUTPUT_DIR=E:\NC
7 T: x( {' T) \" u) Y) A! TUGII_CHARACTER_FONT_DIR=D:\Kasa\ugfonts
1 l. d, a) V2 Z# IUGII_DMX_NX502=1
UGII_ENABLE_TRANSFORM_LEGACY_OPTIONS=1

自己写的加进去了，无效，不知道怎么回事。

zzzzz12345

好简单的啊。

xhujun2

给你个批处理文件参考一下，其实很简单
@echo off
set UGII_LANG=Simpl_chinese
+ k: h1 S. _& J; L& y1 I7 yset UGII_CAM_POST_OUTPUT_DIR=D:\NC\
set UGII_SYMBOL_LIBRARY_DIR=D:\***\symbol\
4 M$ l3 i! z0 m1 N6 F2 W. @set UGII_CHARACTER_FONT_DIR=D:\***\ugfonts\
set UGII_CAM_POST_DIR=D:\***\postprocessor\
& n0 A  O4 u8 Aset UGII_CAM_TEMPLATE_SET_DIR=D:\***\template_set\
set UGII_LOCAL_USER_DEFAULTS=D:\***\setup\nx4_user.dpv
set UGII_USER_DIR=D:\***\
set UGII_CUSTOM_DIRECTORY_FILE=D:\***\setup\custom_dirs.dat
copy/y "d:\ju_conf\application\elec_draw_a_48.dll" "d:\ju_conf\application\elec_draw_a.dll"
3 a, s& R, B! M, e8 H, Bcopy/y "d:\ju_conf\application\elec_draw_48.dll" "d:\ju_conf\application\elec_draw.dll"
) r+ Y4 R8 m# k  j. t& c* @* [1 _copy/y "d:\ju_conf\application\elec_draw3_48.dll" "d:\ju_conf\application\elec_draw3.dll"
1 ?4 R9 B4 c0 Kcopy/y "d:\ju_conf\application\elec_draw5_48.dll" "d:\ju_conf\application\elec_draw5.dll"
copy/y "d:\ju_conf\application\elec_draw15_48.dll" "d:\ju_conf\application\elec_draw15.dll"
copy/y "d:\ju_conf\application\post_prog_act_48.dll" "d:\ju_conf\application\post_prog_act.dll"
copy/y "d:\ju_conf\application\post_prog_select_48.dll" "d:\ju_conf\application\post_prog_select.dll"
! @' f7 G8 [* A! O$ ~6 x7 B% Ucopy/y "d:\ju_conf\application\post_prog_48.dll" "d:\ju_conf\application\post_prog.dll"
copy/y "d:\***\startup\***_nx4" "D:\***\startup\***.tbr"
start "Title" "D:\***\setup\NX 4.0.lnk" %*
exit
  c# a- g/ w6 E, {# ~% {

盗走我的坟

xhujun2 发表于 2013-6-22 15:13
给你个批处理文件参考一下，其实很简单
1 a& F8 l% B$ c  t8 o@echo off
set UGII_LANG=Simpl_chinese

( |  F1 s+ o0 n' m/ I) r9 v谢谢你，看到你的头像很熟悉。真心谢谢，我去试试看。