自制五轴后处理，但是不知哪里出了错

LEIZHONGKE · 发表于 2017-4-14 19:00

大师，想请教下，我用ductpost做了个HEAD-TABLE五轴的后处理，但是不知道哪里出了错，除了不了。

#################################################
# Company -                                        #
# Machine - GENERIC                               #
# Control - FANUC18MB                               #
#                                              #
# Axis Configuration Code : 5202             #
#                ---------------             #
#                      | HEAD  | TABLE |       #
#  ---------------|-------|-------|             #
# | A axis       | -       | X |             #
# |---------------|-------|-------|             #
# | B axis       | -       | Y |             #
# |---------------|-------|-------|             #
# | C axis       | -       |    |             #
#  -------------------------------             #
#                                              #
# Metric output                      |  1  |       #
# Absolute output                |  1  |             #
# Cutter Compensation                |  1  |             #
# Drilling cycles                |  1  |             #
# Drilling cycles 200 series       |  0  |             #
# Parameterised feedrates       |  0  |             #
# Inverse time feedrates       |  0  |             #
# RTCP                               |  0  |             #
# Active Working Plane             |  0  |             #
# Connection moves enabled       |  1  |             #
# Spline machining             |  0  |             #
#                                              #
#################################################
#
#
# Created by       - jla - 27.02.2003
#
#
#
#38
  define word %D
address letter = "( Date : "
address width  = 9
field width = 2
  end define
#44
  define word %M
address letter = "."
address width  = 1
field width = 2
  end define
#50
  define word %Y
address letter = "."
address width  = 1
field width = 2
  end define
#56
  define word %h
address letter = " - "
address width  = 3
field width = 2
  end define
#62
  define word %m
address letter = ":"
address width  = 1
field width = 2
decimal places = 0
decimal point  = false
  end define
#70
  define word %s
address letter = ":"
address width  = 1
field width = 2
  end define
#76
  define word TPN
address letter = "( TOOLPATH - "
address width  = 13
field width = 20
  end define
#82
  define word TNO
address letter = "( TOOL NO."
address width  = 10
field width = 3
decimal places = 0
decimal point  = false
leading zeros  = false
trailing zeros = false
  end define
#92
  define word TN
address letter = "( TOOL ID : "
address width  = 14
field width = 30
  end define
#98
  define word TT
address letter = "( TOOL TYPE : "
address width  = 14
field width = 32
decimal places = 0
decimal point  = false
leading zeros  = false
trailing zeros = false
  end define
#108
  define word TD
address letter = "( TOOL DIA. "
address width  = 12
field width = 8
scale factor = 2
decimal places = 3
decimal point  = true
leading zeros  = false
trailing zeros = false
  end define
#119
  define word TR
address letter = " TIP RAD "
address width  = 9
scale factor = 1
field width = 8
decimal places = 3
decimal point  = true
leading zeros  = false
trailing zeros = false
  end define
#130
  define word TLH
address letter = " LENGTH "
address width  = 8
scale factor = 1
field width = 8
decimal places = 3
decimal point  = true
leading zeros  = false
trailing zeros = false
  end define
#141
  define word TOL
address letter = "( Tolerance = "
address width  = 14
field width = 5
decimal places = 3
decimal point  = true
leading zeros  = false
trailing zeros = false
  end define
#151
  define word THK
address letter = "( Allowance = "
address width  = 14
field width = 7
decimal places = 3
scale factor = 1
decimal point  = true
leading zeros  = false
trailing zeros = true
sign          = always
  end define
#163
  define word VER
address letter = "( DP Version : "
address width  = 15
field width = 4
tape position  = 1
  end define
#170
  define word OFN
address letter = "  Option File : "
address width  = 16
field width = 32
tape position  = 0
  end define
#177
  define word M3
address letter  = "M"
address width = 1
field width    = 3
tape position = 1
  end define
#184
  define word DW
address letter = "P"
address width  = 1
metric formats
scale factor = 100
decimal places  = 0
decimal point = false
trailing zeros = true
tape position = 1
  end define
#195
  define format ( ID )
address letter = "O"
field width = 4
  end define
#200
  define format ( G4 H )
leading zeros  = true
  end define
#204
  define format ( P )
field width = 4
leading zeros = true
  end define
#209
  define format ( A B C )
field width = 9
decimal places = 3
decimal point  = true
leading zeros  = true
trailing zeros = true
sign          = if negative
modal
  end define
#219
  define format ( H M1 )
modal
  end define
#223
  word order = ( N )
#225
  define keys
drill peck depth = Q1
drill hole depth = Z2
clearplane    = R2
cycle dwell    = DW
azimuth axis    = B
elevation axis = A
spindle
  end define
#235
  define codes
cycle retract = G6 98
drill          = G4 82
break chip    = G4 83
deep drill    = G4 83
tap             = G4 84
bore 1          = G4 85
bore 2          = G4 76
coolant on mist  = M2 51
  end define
#246
  message output       = false
  block order          = true
  tool reset coordinates = 3
  counter start       = 1
  counter increment    = 1
  integer 69          = 2
  maximum feedrate = 99999.0
#254
  spindle azimuth rotation = false
  azimuth axis units       = degrees
  azimuth axis direction    = positive
  azimuth centre          = ( 0.0  0.0  0.0)
  azimuth axis parameters = ( 0.0 0.0 0.0  1.0 0.0 0.0)

  spindle elevation rotation = true
  elevation axis units    = degrees
  elevation axis direction = positive
  elevation centre          = ( 0  0  0 )
  elevation axis parameters  = ( 0.0 0.0 0.0  0.0 0.0 350.0)
#
  pcs origin                = ( 0  0  0  0  0  0 )
  linear axis limits       = ( -9999.0 9999.0 -9999.0 9999.0 -9999.0 9999.0 )
  rotary axis limits       = ( -360.0 360.0  -85.0 85.0  0.05  1.0 )
#
  initial tool vector          = ( 0 0 1 )
#
  # workplane angles             = machine tool


# workplane origin shift = false
# retract and reconfigure style = none  linearise combine
# expand helical drilling cycles = true
# contact point based feedrate = true

   workplane angles             = none
  retract at angular limit    = true
  unwind at tool change       = true
  multiaxis coordinate transform = true
  linearise multiaxis moves    = true
  withdrawal amount             = 100.0
  integer 3                   = 1
#279
  define block tape start
"%"
ID JobName
N ; %D Day ; %M Month ; %Y Year ; %h Hour ; %m Minutes ; %s Seconds ; " )"
if ( DPversion < 1400 )
   error " MINIMUM DUCTPOST VERSION REQUIRED = 1400"
end if
N ; VER DPversion ; OFN OptionFileName ; " )"
N ; G2 40 ; G3 17 ; G4 80 ; G6 49 ; G5 90

  if ( ToolPath5axis )
   N ; "M74 "
   else
   N ; "M71 "
  N ; "M73 "
   end if
end define

#290
  define block tool change first
N ; TT ToolType ; " )"
N ; TN ToolName ; " )"
if ( ToolType = "BALLNOSED" or ToolType = "ENDMILL" or ToolType = "DRILL" )
   N ; TD ToolRadius[ToolNum] ; TLH ToolLength[ToolNum] ; " )"
else
   N ; TD ToolRadius[ToolNum] ; TR TipRadius[ToolNum] ; TLH ToolLength[ToolNum] ; " )"
end if
N ; change tool ; T ToolNum
N ; S toolSpeed[ToolNum] ; spindle on cw
N ; rapid =C ; G4 54 =C ; x coord FromX =C ; y coord FromY =C
N ; G6 43 ;  "H11"
N ; abs data =C ;
  end define
#305
  define block tool change
N ; TT ToolType ; " )"
N ; TN ToolName ; " )"
if ( ToolType = "BALLNOSED" or ToolType = "ENDMILL" or ToolType = "DRILL" )
   N ; TD ToolRadius[ToolNum] ; TLH ToolLength[ToolNum] ; " )"
else
   N ; TD ToolRadius[ToolNum] ; TR TipRadius[ToolNum] ; TLH ToolLength[ToolNum] ; " )"
end if
N ; change tool ; T ToolNum
N ; S toolSpeed[ToolNum] ; spindle on cw
N ; rapid =C ; G4 54 =C ; x coord FromX =C ; y coord FromY =C
N ; G6 43 ;  "H11"
N ; abs data =C ;
  end define
#320
  define block move from
N ;
  end define
#324
  define block cldat 1094
set swa
set swb
  end define
#329
  define block move rapid
if ( swa )
   N ; "( ======== )"
   N ; TPN ToolPathName ; " )"
   N ; "( ======== )"
   unset swa
else
   N ; G1 ; G2 ; G4 ; G5 ; x coord ; y coord ; z coord ;
         elevation axis ; spindle ; M1 ; M2
end if
  end define
#341
  define block move linear
if ( swa )
   unset swa
   N ; "( ======== )"
   N ; TPN ToolPathName ; " )"
   N ; "( ======== )"
end if
if ( swb )
   N ; G1 =C ; G2 ; G5 ; x coord =C ; y coord =C ; z coord =C ;
      azimuth axis =C ; elevation axis =C ; spindle ; feedrate =C ; M1 ; M2
   unset swb
else
   N ; G1 ; G2 ; G5 ; x coord ; y coord ; z coord ;
         elevation axis; spindle ; feedrate ; M1 ; M2
end if
  end define

#383
  define block move cycle
N ; x coord ; y coord ; z coord ; feedrate
  end define
#387
  define block move tap
N ; x coord ; y coord ; z coord ; feedrate
  end define

#400
  define block tape end
N ; G5 91 ; G6 28 ; z coord 10 =C
N ; G6 28 ; y coord 0 =C
N ; "M71 "
  N ; "M73 "
N ; M1 30
"%"
  end define

来自圈子: CAM

塑运塑胶集团 · 发表于 2017-11-5 13:42

我用UG做设计，我骄傲！

向往蓝天 · 发表于 2018-1-21 09:33

我是UG爱好者，看了LZ的帖子，我只想说一句楼上的贴很好！UG论坛好强大！

		自动登录	找回密码
密码			注册

自制五轴后处理，但是不知哪里出了错

浏览过的版块